Pneumatic Tools  
Pneumatic stone hammer for carving, pneumatic central water polishing machine, pneumatic die grinder for stone carving
 
Continue shopping                                           XE.com Personal Currency Assistant
 
**For maintenance of your pneumatic tool: use only acid and resin-free light oil specially for lubrication**
: Qty:
Pneumatic rockdrills PL5
Model    weight     air consumption     Hit/min
PL5     6.0kg     7.5 l/s                         3700  
 
: Qty:
 
 
 
MR series pneumatic stone hammer for carving
Pneumatic stone hammer for carving is used together with the pneumatic carbide tip bushhammer. The MR series pneumatic stone hammer is a very powerful machine and much recommended when carving in granite. However, for letter carving purposes only, MR12 pneumatic stone hammer will suffice for this purpose and you can find the corresponding pneumatic carbide tip chisels in our store as well. Please make sure you choose the correct shank size of pneumatic carbide chisel that match to you pneumatic stone hammer when you purchase them.
 
Available in following sizes:- 
 
Model    weight     air consumption    shank             Hit/min
MR12     0.7kg     2.5 l/s                   Ř12.5mm      6500                                           
MR16     0.9kg     3.0 l/s                   Ř12.5mm      5600
MR22     1.4kg     4.0 l/s                   Ř12.5mm      5000
MR26     2.1kg     6.0 l/s                   Ř15.5mm      4000
 
: Qty:
: Qty:
: Qty:
: Qty:
 
Pistol soft grip pneumatic hammer with Ř12.7mm shank NEWS!!
Supply this pneumatic hammer with 52-82psi (3.5-5.5bar) of clean dry air. Use only acid-and resin-free light oil resp. special pneumatic oils for lubrication. This pneumatic hammer has a sound pressure level at 95dBA and sound power of 102dBA. Never operate the pneumatic hammer without a tool being fully inserted or allow the tools to be driven out of the bushing. If the piston strikes the bottom of the cylinder, it will cause severe internal damage to the pneumatíc hammer.
 
Model         weight     air consumption    shank             Hit/min
Pístol type   0.8kg      200 1/m               Ř12.7mm     5500  
 
: Qty:
 
Chiselling pneumatic hammer CP711 con.
Original  "Chicago Pneumatic" for light to medium heavy work. Its lightweight design makes this pneumatic hammer a good choice for bush hammering eg. facades. Conical shank 13.
Model         weight     air consumption    shank             Hit/min
Pístol type   1.4kg      230 1/m               13 conical    3300
 
 
 
Pneumatic water feed polishing machine model 220 : NEW!
With Larger Cylinder & Stronger Gear than pneumatic water feed polishing machine model 218
Pneumatic Wet/Waterfeed Stone Polisher (3600rpm, Rear Exhaust)
Rear Exhaust
Spindle Size :  M14
Max. Speed : 3,600 rpm
Weight : 1.27 kgs
Length : 234 mm
Air Cons : 0.37 m3/min
Air Inlet : 1/4"
Hose Size : 6.5 mm(I.D.)
Sound Pressure : 84 dBA
Vibration : < 2.5 m/sec2
Air Pressure : 90 psi
: Qty:
Pneumatic die grinder
 
 
 
For fine job eg sculptures and decorations work 
* Maximum RPM is 35000 
* 6mm connection 
* weight 0.35kg , length 175mm
* air consumption 0.17m3/min
* air inlet 6.25mm
 
: Qty:
 
Pneumatic die grinder with protection guard
* Maximum 30000 rpm
* 6mm connection
* weight 0.54kg, length 255mm
* air consumption 0.17 m3/min
* air inlet 6.25mm
 
: Qty:
 
Sandblasting machine - pressure blaster
A small portable sandblasting machince or shortly known as pressure blaster for some small job. Simple and economical yet high quality pressure blaster.
* 500x560x850mm
*34 kg in weight
* 4-7 bar
*24L tank capacity